實驗概要
The procedure presented below describes a facile method for studying signal transduction events with adherent cells (HeLa, MCF-7, BALB/c 3T3, etc.). In this procedure, cells are gently lifted from their culture vessel, placed into wells of a 96-well filter bottom plate, and stimulated as desired. At the end of stimulation, cell culture medium is removed from the bottom of the wells by gentle aspiration using a vacuum manifold. The cells are then washed with PBS, aspirated, and lysed within the wells by addition of Cell Extraction Buffer. The cell extracts are then assayed using Invitrogen? p38MAPK [pTpY180/182] and p38MAPK (total) phosphoELISA? kits.
實驗材料
The following materials will be needed:
Trypsin/EDTA solution (Cat. no. 25300-054)
Complete Cell Culture Medium (e.g., DMEM plus 10% FBS)
PBS (Invitrogen Cat. nos.11885-076 and 26140-079)
Cell Extraction Buffer (Cat. no. FNN0011)
Orbital Plate Shaker (Lab Line Titer Plate Shaker Cat. no. 4625-EA)
p38 MAPK [pTpY180/182] phosphoELISA? (Cat. no. KHO0061)
p38 MAPK Total phosphoELISA? (Cat. no. KHO0071)
BD Falcon 96-well cell culture plate (BD Cat. no. 353072)
Cell extraction buffer formulation:
10 mM Tris, pH 7.4 ? 2 mM Na3VO4
100 mM NaCl ? 1% Triton X-100
1 mM EDTA ? 10% glycerol
1 mM EGTA ? 0.1% SDS
1 mM NaF ? 0.5% deoxycholate
20 mM Na4P2O7 ? 1 mM PMSF (stock 0.3 M in DMSO)
Prepare Protease Inhibitor Cocktail (Sigma Cat. no. P-2714) according to the manufacturer’s guideline as a 10x stock. Add 100 μl per 1 ml Cell Extraction Buffer.
實驗步驟
1. Grow cells to desired level of confluency in a T75 flask.
2. Decant or aspirate the medium.
3. Add 2–3 ml fresh warm trypsin/EDTA solution. Transfer the flask to a 37°C incubator.
4. Wash with warm PBS. Aspirate.
5. After 5 minutes, tap the side of the flask, and examine the flask under a microscope for lifting. If necessary, return the cells to the incubator for an additional 5–10 minutes, with occasional tapping, until lifting is complete.
6. Quickly quench the Trypsin reaction by adding 5–6 ml Complete Cell Culture Medium.
7. Transfer the cells to sterile 15 ml conical tubes.
8. Pellet the cells by centrifugation at 300 x g for 7 minutes.
9. Decant the supernatant.
10. Wash the cells by pipetting 10 ml medium into each conical tube and resuspending the pellet. Collect the cells by centrifugation at 300 x g for 7 minutes.
11. Resuspend the washed cells in complete cell culture medium.
12. Enumerate cell density. For most applications, the cell density should be adjusted to 5–25 x 104 cells/ml cell culture medium. It is important to note that this value may require some optimization for each specific application. Cell doubling time is an important factor to be considered when adjusting cell density at the beginning of an experiment.
13. Plate 200 μl of cell culture (i.e., 10,000–50,000 cells) into the wells of the sterile 96-well cell culture plate. Incubate the cells for 18 hours at 37°C.
14. Stimulate the cells as desired. In the example presented below, HeLa cells were treated with 100 μM anisomycin for 60 minutes at 37°C.
15. At the end of the treatment, aspirate the media from the wells.
16. Wash the cells by pipetting 200 μl ice-cold PBS into each well. Remove the PBS by aspiration and repeat two times for a total of three washings.
17. Aspirate the medium. Pipette 25 μl protease-inhibitor-supplemented Cell Extraction Buffer into each well. Incubate the plate on ice for 30 minutes.
18. Thoroughly mix the contents of each well by pipetting up and down 5–6 times. A multi-channel pipette is desirable for this application. This procedure causes the cells to lyse. At this point in the procedure, the extracts are ready for analysis. Alternatively, the extracts may be stored in the filter bottom plate at –20°C for future analysis. Frozen plates should be thawed on ice in preparation of completing the assays.
19. Place the plate on an orbital shaker and mix for 1 minute.
20. Prepare the phosphoELISA? kits. Sample Wells: Pipette 95 μl Standard Diluent Buffer (included in the kits) into the wells of the phosphoELISA? plates designated for samples. Transfer 5 μl cell extract from the filter plate into the sample wells of the plates. Place the plates on an orbital shaker to thoroughly mix the contents of the wells. Standard Wells: Prepare standards as indicated in the assay protocol and pipette into designated wells.
21. Complete the phosphoELISA? as directed by the assay protocol.